Free express shipping over $99 GRA & IGI certificates Quote in 1 business day

Journal / Wedding Bridal

Wedding & Bridal Sets: Vetting a Factory: Seven - HOLYCOME
HOLYCOME / NOTESWedding Bridal  ●  16 November 2026  ●  6 MIN

Wedding & Bridal Sets: Vetting a Factory: Seven - HOLYCOME

This guide walks a wholesale or boutique buyer through wedding the way our bench would talk it through on a sample day: what the order actually consists of, where the cost sits, and the checks that decide whether the lot lands clean on your shelf. No catalogue adjectives, just the numbers and the decisions we see buyers get wrong most often.

Ask for the certificate and the alloy declaration in writing. A GRA or batch card declares grade and carat; it is not the same as an independent laboratory report, and the listing should say which one applies. For metal, the alloy sheet states the silver grade or the gold karat and confirms whether any nickel is added, which matters for customers with sensitive skin.

Reject on documented defects, not on taste: a tilted stone, a prong on the table, a plating gap at the inner shank, or a weight under spec are all measurable. Photograph the batch before it leaves the bench so a later complaint has a baseline. A supplier that pushes back on a documented defect is one you will spend the whole order negotiating with.

A first sample tells you more than a catalogue of five. On the sample, check the band or shank weight against the spec, look at the plating under a loupe at the high-friction points, confirm the stone sits level and the prongs sit above the girdle, and weigh the piece. A hollow or underweight body is the first thing a repeat order exposes.

[1]Wedding: the practical checks before you order

  • Photograph the batch on arrival so any later defect claim has a baseline to compare against.
  • Confirm the stone grade and carat on the spec sheet, and note whether it ships on a batch card or a per-stone report.
  • Weigh the piece against the listed weight; an underweight shank or body is usually the first sign of a thin build.
  • Check the plating or finish at the high-friction points under a loupe, where wear shows first.
  • Verify the prongs sit above the girdle and the stone sits level; a tilted stone reads as a cheap setting in any photo.

[2]Planning the first run

Mixing the range on the first order is a judgment call. A small number of proven designs at a workable MOQ gives the bench less to set up and the buyer fewer decisions to defend if something underperforms. Reserve the experimental finishes and newer shapes for a later batch, once the core of the catalogue has proved itself with your customers.

Payment and sample terms should be settled before production starts. A sample order, the approved spec sheet, and the deposit schedule are the three documents that keep a bulk run from becoming a negotiation halfway through. If a supplier is vague on which of these are written down, that vagueness usually repeats on delivery day.

[3]Reference range in our catalogue

ReferenceSpecificationMOQUnit range
Moissanite Wedding Band MA146Moissanite · 925 Sterling Silver1on request
Moissanite Wedding Band NS-0740Moissanite · 925 Sterling Silver1on request
Wheat-Weave Wedding Band925 Sterling Silver1on request

Ranges reflect current factory pricing for this catalogue and move with metal and stone costs; treat them as planning figures and confirm against a written quotation.

A buyer who asks for the sample, the spec sheet and the certificate first usually places the cleaner reorder. The supplier that resists those three before the first deposit is telling you something useful already.

The practical takeaway is straightforward: read the spec sheet before the price, hold the sample before the bulk, and judge the lot on weight, finish and stone match rather than on listing imagery. Do that consistently and the repeat orders mostly take care of themselves.

[4]Buyer questions

What should I check on the first sample?

Weight against spec, plating under a loupe at friction points, stone levelness, prong position and overall weigh-in. Photograph the sample on arrival as the baseline for the bulk lot.

Which certificate or declaration matters?

The stone card or report number and the alloy declaration. Confirm whether the certificate is a batch card or a per-stone report, and keep the number matched to the parcel records.

Can I order a sample before committing to bulk?

Yes. A sample from stock lets you judge weight, finish and communication before the bulk run; compare it against the spec sheet and keep arrival photos for the later comparison.

[5]Related reading

Ready when you are

Send a photograph. Get the price tomorrow.

Request a quote WhatsApp us

MOQ for a single commission is 1 piece; wholesale MOQ is 20 pcs per style. Sampling takes 7-14 days, bulk 15-25 days after CAD approval. Payment is T/T with a 30% deposit, balance before shipment; PayPal and major cards are accepted.

Every piece passes a quality check before dispatch, and authenticity is matched to its certificate, with a return policy and repair service after delivery. Our in-house jewelers and artisans have years of experience setting moissanite and lab-grown stones from responsible, traceable suppliers; customer reviews and commission testimonials are shared in our journal and on the about page. Questions? Email service@holycome.com or WhatsApp +86 13377447107.

WhatsApp us Get a quote
WhatsApp Email