Free express shipping over $99 GRA & IGI certificates Quote in 1 business day

Journal / Wedding Bridal

Wedding Band Engraving Depth Limits
HOLYCOME / NOTESWedding Bridal  ●  9 November 2026  ●  8 MIN

Wedding Band Engraving Depth Limits

A buyer in Seattle ordered 120 wedding bands with a 0.3 mm engraved message inside and had 14 back within two years with a crack along the text. The engraving was correct and the wall beneath it was not.

Inside engraving is a cut into the thinnest part of a band, and its depth limit is a function of the band's thickness rather than of the font. A supplier who engraves to a fixed depth on every width will crack the narrow ones.

[1]The rule that governs depth

Leave at least 65 percent of the original wall below the deepest point of the cut. A band that starts at 1.4 mm cannot carry a cut deeper than 0.5 mm, and a 0.25 mm cut is the practical ceiling once polishing is counted.

The rule is a fraction rather than a number, because band thickness varies by width and by size. A 2 mm band at size 5 is thinner than the same band at size 9, since the metal is rolled from a fixed blank.

Band thicknessMax depthPractical depthMethod
1.2 mm0.42 mm0.20 mmLaser only
1.4 mm0.49 mm0.25 mmLaser only
1.6 mm0.56 mm0.30 mmLaser or hand
1.8 mm0.63 mm0.35 mmLaser or hand
2.2 mm0.77 mm0.45 mmHand engraving

The practical depth is lower than the calculated maximum because polishing removes 0.05 to 0.1 mm from the inside surface after engraving, and that removal happens after the cut has already reduced the wall.

Half eternity diamond wedding band in white metal

[2]Laser against hand engraving

A laser cuts to a controlled depth with a narrow kerf, and it can hold 0.15 mm consistently across a run. Hand engraving removes metal with a graver and the depth varies with the engraver's pressure, which is a range rather than a number.

On a 1.4 mm band the laser is the only method that can hold the limit. On a 2.2 mm band hand engraving gives a deeper, warmer line and the depth variation stays inside the allowance.

Why the laser still cracks bands

A laser that is set to a fixed power and a fixed pass count cuts deeper on a thin band than on a thick one, because the same energy removes a larger fraction of the wall. The fix is a power setting by thickness, not a single recipe.

A workshop that engraves every band with one recipe will produce a run that is fine on the wide sizes and cracked on the narrow ones, and the cracks appear months later along the baseline of the text.

[3]Where the crack starts

The crack starts at the deepest point of the cut, which is usually the descender of a letter or the end of a line where the laser dwells. A long message with tight spacing concentrates the cuts and reduces the wall between them.

A 40 character message on a narrow band cuts more metal than a 15 character message, and the risk is cumulative rather than linear. The character budget should be set by band thickness.

The character budget

A 1.4 mm band holds about 18 characters at 0.25 mm depth in a 2.5 mm font. A 1.8 mm band holds about 28. A 2.2 mm band holds 40 or more, which is where a full date and two names fit.

A buyer who wants a long message on a narrow band should be offered an outside engraving or a wider band, and both options are cheaper than a remake.

[4]What the font does

A serif font has thin strokes and thick strokes, so its deepest cut is variable. A sans serif font has a uniform stroke and a uniform depth, which is why it is the default for laser engraving on a thin band.

A script font has long connected strokes that cross the band's centreline, which is the thinnest region on a comfort fit band. That combination is the highest risk in the category.

[5]What to specify

Four items: the band's finished thickness, the font, the character count and the maximum depth. A work order with those four lets the engraver set the recipe before the first piece rather than after the run.

The finished thickness matters because the blank thickness is not the delivered thickness. A band that is 1.6 mm before polishing and 1.5 mm after carries a different limit than the spec sheet suggests.

[6]What we do

We set the laser recipe by measured thickness, cap the character count by band width, default to a sans serif on bands under 1.6 mm, and engrave a test piece from the run before the batch. Buyers with a long message are offered an outside line or a wider band.

Minimum order is 50 pieces per design and sizes can be mixed. Sample lead time is around 20 days from approved CAD, bulk 25 to 30 days, and stock designs ship in 15 to 20 days under 500 pieces. Payment is a 30 percent deposit with the balance before shipment, by T/T, PayPal or Western Union.

[7]The comfort fit problem

A comfort fit band is thinner at the centre of the inside surface than at the edges, because the bore is curved and the wall follows it. On a 2 mm comfort fit band the centreline can be 0.25 mm thinner than the edge, which is exactly where a script font crosses.

That means the thickness a supplier checks at the edge is not the thickness the engraving sees. The measurement has to be taken at the centre of the band's inside face, on the line the text will follow.

A buyer who specifies a comfort fit and a long inside message is specifying two things that work against each other, and the conflict should be raised at the order rather than discovered at the return.

[8]What a remake costs against a re-tip

A cracked band cannot be repaired invisibly. A weld along the engraving destroys the text, so the options are a re-engrave on the same band after welding, or a remake in the same design.

A remake carries the full cost of the band plus the engraving plus the freight, which on a 120 piece order is a line item rather than a rounding error. A cracked band out of every eight is a 12 percent remake rate, which is higher than the margin on that design.

The prevention is a test piece from the run, engraved and inspected before the batch. It costs one band and it converts a remake rate into a setting change.

[9]Engraving a band that may be re-sized

A re-size cuts the band at the bottom and adds or removes metal, which usually leaves the inside engraving intact if the text sits opposite the cut. A long message that runs the full circumference will be cut, whatever the re-size.

The practical rule is to keep the message within 40 percent of the circumference and centred opposite the sizing point, which leaves the joint clear. That rule costs nothing at the order stage and protects the text at any later re-size.

A band that has already been engraved and then re-sized may need the text re-cut after the weld, and the re-cut has to respect the new thickness at the joint rather than the original one.

[10]What a buyer should test before the run

Two checks on a test band: measure the inside thickness at the text line with a micrometer, and inspect the deepest cut under a loupe for a bright line at the base of the stroke.

A bright line at the base of a stroke is the metal showing through, which means the cut is at the limit. It is visible at 10x and invisible at arm's length, which is why the check belongs at the bench rather than at delivery.

A test band that passes both checks predicts the run within a few percent, because the variables are thickness and recipe rather than operator skill.

[11]Frequently Asked Questions

How deep can engraving be inside a wedding band?

A quarter of the finished thickness at most, and 0.25 mm on a 1.4 mm band is the practical ceiling once polishing is counted.

Does laser engraving weaken a band?

It removes metal at the cut, so it weakens the wall by the depth of the cut. A controlled depth keeps the loss inside the allowance.

How many characters fit inside a band?

About 18 on a 1.4 mm band, 28 on a 1.8 mm, and 40 or more on a 2.2 mm. The budget follows the thickness, not the font size.

Can a band be engraved after it is polished?

Yes, and the recipe has to be set on the polished thickness. Engraving before polishing and then polishing over the cut loses the edge of the letters.

[12]Next step

Send the band width, the message and the font, and we will return the character budget and the depth for that thickness. See wedding band work in the archive, read the journal on band width pairing, or open a brief on the contact page.

Ready when you are

Send a photograph. Get the price tomorrow.

Request a quote WhatsApp us

MOQ for a single commission is 1 piece; wholesale MOQ is 20 pcs per style. Sampling takes 7-14 days, bulk 15-25 days after CAD approval. Payment is T/T with a 30% deposit, balance before shipment; PayPal and major cards are accepted.

Every piece passes a quality check before dispatch, and authenticity is matched to its certificate, with a return policy and repair service after delivery. Our in-house jewelers and artisans have years of experience setting moissanite and lab-grown stones from responsible, traceable suppliers; customer reviews and commission testimonials are shared in our journal and on the about page. Questions? Email service@holycome.com or WhatsApp +86 13377447107.

WhatsApp us Get a quote
WhatsApp Email