Free express shipping over $99 GRA & IGI certificates Quote in 1 business day

Journal / Ring Size Fit

Ring Size Tolerance in a Production Run
HOLYCOME / NOTESRing Size Fit  ●  9 November 2026  ●  8 MIN

Ring Size Tolerance in a Production Run

A buyer in Dallas received 200 rings all stamped size 7 and had 11 complaints about one batch that measured 6.75. The stamp was correct, the mould was not.

Ring size is a dimension with a tolerance, and the tolerance is set by the process rather than by the stamp. A run that is checked by stamp is a run that will ship with a size spread.

[1]Where the tolerance comes from

Four steps move a size: the mould's shrinkage, the casting's thermal contraction, the polishing removal and the finishing pass. Each contributes a fraction of a millimetre and the fractions add rather than cancel.

A lost wax casting in silver shrinks about 2 percent from the mould, which on a 17.3 mm size 7 bore is 0.35 mm before any correction. That correction is built into the mould, and a worn mould carries a different correction than a new one.

StepEffect on boreControl
Mould shrink-0.30 to -0.40 mmMould compensation
Casting contraction-0.05 mmMetal and temperature
Polishing+0.05 to +0.12 mmBarrel time
Finishing pass+0.03 mmOperator

The net effect is a bore that lands within a range rather than on a number. A ring 0.15 mm over fits a half size loose, and one 0.15 mm under does not pass the knuckle.

Wide band ring with a polished interior profile on a light surface

[2]The tolerance a run should hold

Plus or minus 0.1 mm on the bore is achievable on a controlled run and it belongs in the specification. That is about one eighth of a size, inside the range a finger tolerates across a day.

Plus or minus 0.2 mm is what a run without a bore check delivers, and that is the range where a customer notices. The difference is a gauge and a check frequency.

[3]How to check a bore

Three tools: a plug gauge, a caliper and master rings. A plug gauge is a go and no-go pair and it checks every piece in seconds, which is the only method that works at volume.

A caliper reads a bore to 0.05 mm and it is slower, so it runs on a sample. A master ring is the reference both tools are set against, and it should be re-certified yearly.

The check frequency

First piece, then every 25 pieces, then every piece after a mould or barrel change. That schedule catches drift before a batch is complete rather than after it ships.

[4]Why the stamp is not the size

A stamp is applied to the finished ring and it records the intended size rather than the measured one. A run that stamps by mould number inherits the mould's drift, and the customer reads the stamp as a promise.

The fix is to stamp after measuring, using the plug gauge result rather than the work order. A ring that measures 6.9 is stamped 7, and a ring that measures 7.1 is held for a re-size.

[5]What a size spread does to returns

A 200 piece run at plus or minus 0.2 mm produces about 6 percent of pieces outside the customer's tolerance, which is 12 rings. Those 12 come back as fit complaints, each costing a return label plus a re-size plus the freight.

A run at plus or minus 0.1 mm produces about 2 percent, which is 4 rings. The difference in return cost usually exceeds the cost of the gauge and the extra checking time.

[6]What to specify on the purchase order

Four items: the bore tolerance in millimetres, the gauge type, the check frequency and the disposition of a piece outside tolerance. A purchase order with those four removes the argument at delivery.

The disposition matters as much as the tolerance, because a supplier who re-sizes without asking changes the ring's proportions. A supplier who holds the piece and reports it lets the buyer decide.

[7]What we do

We specify a plus or minus 0.1 mm bore tolerance, check with a plug gauge at first piece and every 25, and hold out-of-tolerance rings for the buyer's decision rather than re-sizing them. Every shipment carries the measured bore of the sample.

Minimum order is 50 pieces per design and sizes can be mixed. Sample lead time is around 20 days from approved CAD, bulk 25 to 30 days, and stock designs ship in 15 to 20 days under 500 pieces. Payment is a 30 percent deposit with the balance before shipment, by T/T, PayPal or Western Union.

[8]The mould that wears out

A production mould is used for hundreds of castings and its cavity erodes at the edges, which changes the cast ring's outer diameter more than its bore. A worn mould delivers a ring that measures correct inside and thin outside.

That is the opposite of the usual reading of a sizing complaint, because a customer who feels a ring loose assumes the bore is large rather than the wall thin. A caliper on the wall settles it in one measurement.

A mould should be gauged with the first casting of each run and retired when its outer diameter drifts beyond the wall tolerance, which on a 1.8 mm band is 0.1 mm.

[9]The polishing variable

Barrel polishing removes metal evenly from the outside and the inside, and a longer barrel run opens the bore. A 20 minute difference in barrel time moves the bore by about 0.04 mm, which sounds small and accumulates across a run.

The barrel is the step that a workshop controls least precisely, because it runs batches rather than pieces. Setting a barrel time per design rather than per material is the correction.

A buyer who receives a run with a size spread should ask for the barrel time before asking for a re-size, because the spread usually starts there.

[10]Sizing a run for a market

A size run for the United States centres on 6 to 8, and a run that centres on 5 leaves the middle sizes short. The distribution is not symmetric, and the median is the number to build around.

A buyer selling online needs more of the two middle sizes than a boutique, because an online customer self-selects a size and a boutique customer tries three. The two channels want different curves from the same design.

Building the curve from the channel rather than from the country is the difference between a run that sells through and one that ends with a rack of size 5.

[11]What a re-size costs after delivery

A re-size on a plain band costs a bench hour plus the freight and the re-polish, and it returns the ring as a used piece rather than a new one. On a 200 piece run, 12 re-sizes cost more than the gauge that would have prevented them.

A re-size also voids the original polish and the original plating, so the returned ring needs a full refinish before it can be sold again. That refinish is the hidden half of the cost.

The arithmetic favours prevention at every volume above 50 pieces, which is the order size where a plug gauge pays for itself.

[12]The gauge a small buyer should own

A go and no-go plug set for the two or three sizes a buyer sells costs less than a single return and it fits in a drawer. That is the whole case for owning one.

A buyer who cannot justify a gauge can ask the supplier for the measured bore on the sample with each shipment, which shifts the cost to the party that already has the tool.

[13]Frequently Asked Questions

What tolerance should a ring size hold?

Plus or minus 0.1 mm on the bore, which is about one eighth of a size. Anything wider shows up as a fit complaint.

Why do rings from one run fit differently?

Mould wear and barrel time vary across a run, and both move the bore by a fraction of a millimetre. The variation is process rather than operator error.

Can a ring be re-sized into tolerance?

Yes on a plain band. On an eternity or channel band the re-size disturbs the setting, so the piece should be held rather than corrected.

Does the stamp guarantee the size?

No. The stamp records the intended size, and only a gauge records the measured one.

[14]Next step

Send the size run and the band type, and we will quote the bore tolerance and the check schedule for that design. See sizing work in the archive, read the journal on finger temperature, or open a brief on the contact page.

Ready when you are

Send a photograph. Get the price tomorrow.

Request a quote WhatsApp us

MOQ for a single commission is 1 piece; wholesale MOQ is 20 pcs per style. Sampling takes 7-14 days, bulk 15-25 days after CAD approval. Payment is T/T with a 30% deposit, balance before shipment; PayPal and major cards are accepted.

Every piece passes a quality check before dispatch, and authenticity is matched to its certificate, with a return policy and repair service after delivery. Our in-house jewelers and artisans have years of experience setting moissanite and lab-grown stones from responsible, traceable suppliers; customer reviews and commission testimonials are shared in our journal and on the about page. Questions? Email service@holycome.com or WhatsApp +86 13377447107.

WhatsApp us Get a quote
WhatsApp Email