Journal / Wholesale Oem Factory
OEM Sample Approval and the Golden Sample
A brand in Los Angeles approved a sample in June and received 500 pieces in September with a shank 0.4 mm narrower. The sample was correct; nothing recorded what had been approved.
The gap between an approved sample and a bulk run is closed by paperwork rather than by trust, and the paperwork is short.
[1]What a golden sample is
A golden sample is the piece both parties agree is correct, sealed and signed, kept by the buyer and by the factory. It is the physical definition of the order.
Without it, a dispute about width, finish or stone colour has no reference, and the conversation becomes a matter of memory. With it, the comparison is a measurement.
| Document | What it fixes | Who keeps it |
|---|---|---|
| Golden sample | Shape, finish, colour | Both parties |
| Tolerance sheet | Numbers on key dimensions | Both parties |
| Stone record | Size, grade, count | Both parties |
| Approval photo | Appearance at approval | Buyer |
The four documents overlap on purpose. A photo shows appearance, the sample shows feel and finish, the sheet shows numbers and the stone record shows the parcel.

[2]The tolerance sheet
A tolerance sheet states the permitted range for every dimension that matters, and it is the document that turns a sample into a specification.
Band width plus or minus 0.15 mm, thickness plus or minus 0.1 mm, stone diameter plus or minus 0.1 mm, total weight plus or minus 5 percent. Those four cover most disputes.
Why tolerances are needed
A cast piece cannot be made to an exact number at production volume, and a specification that demands an exact number will be rejected at inspection. A tolerance states what is acceptable before production rather than after.
What happens without one
The factory works to its own tolerance, which is usually wider than the buyer's expectation. The gap appears at delivery and it is usually 0.2 to 0.4 mm on a band width, which is enough to change how the ring reads.
[3]Sealing and signing
The golden sample should be sealed in a tamper evident bag, signed across the seal by both parties, and dated. A sample that can be opened is a sample that can be replaced.
The seal matters because the failure is rarely a factory that ignored the sample. It is a factory that lost it, or a bench that used a similar piece from an earlier order.
[4]Approval before production
Production should not start until the golden sample is sealed and the tolerance sheet is signed. That sequence is what the deposit is paying for, and reversing it removes the only control point in the process.
The photo set
Six photographs: front, side, top, interior, setting detail and stone detail, all under the same light. A photo set taken at approval is the only record of what the piece looked like before wear and before shipping.
[5]The reorder problem
A reorder is the moment a golden sample earns its cost, because a reorder is made against the master rather than the original CAD. A master that has been stored correctly reproduces the piece; one that has been handled or re-cut does not.
On a reorder we open the sealed duplicate and measure three dimensions before the first casting. That check takes an hour and prevents a run that is 0.3 mm off the original.
When a reorder needs a new sample
When the metal changes, the stone changes or the size range changes. Those three alter weight and appearance, and a golden sample from a different metal is not a reference for a new one.
[6]What a failed approval costs
A failed approval costs a second sample plus the time between them, which is usually three to four weeks. On a launch order that is the launch.
It also costs a second round of shipping and a second round of the buyer's own review time, which is rarely counted and always real. The total is usually 6 to 10 percent of the order value before the bulk is even started.
Where approvals fail
Three causes: a CAD that was not approved before the master was cut, a finish that was approved in a photograph rather than in the hand, and a stone that was approved as a grade rather than as a specific parcel.
All three are documentation failures rather than manufacturing failures, and all three are prevented by the four documents above.
A fourth cause is a sample approved by one person and production ordered by another. A single approver with a signature on the sheet closes that gap, and it costs nothing.
[7]Where the sample lives
The buyer's sample lives in a sealed bag in a drawer, and the factory's duplicate lives in a master vault indexed by design number. A factory that keeps samples on an open shelf is a factory that will use the wrong one.
The index matters as much as the vault. A design number that cannot be found is the same as a master that was never kept.
[8]Payment and deposit structure
A first order is usually 30 percent deposit with the balance before shipment. The deposit covers the master, the mould and the metal purchase, which is why it is paid before those three start rather than on approval of the sample.
A buyer who wants the deposit to follow the sample approval should agree that in writing, because the master cut is the part of the process that cannot be undone.
The second order
A reorder has no master cost and a smaller deposit is reasonable, since the mould already exists. Factories that keep the same terms on a reorder are covering a risk that is no longer there.
A reorder also has a shorter schedule, because the CAD and the mould are already done. A factory that quotes the same lead time on a reorder is quoting the first-order sequence out of habit rather than from its own calendar.
What the balance releases
The balance releases the goods, and it usually follows an inspection rather than a date. An inspection before the balance is the buyer's only leverage, and it is worth scheduling.
[9]What the order file contains
Six items: the CAD, the sealed sample, the tolerance sheet, the stone record, the plating specification and the approval photographs. A file with those six can be handed to a bench and reproduced without a conversation.
A file missing any of them requires a conversation at production time, which is the most expensive moment to have one.
[10]What we do
We seal the golden sample with the buyer's signature, issue a tolerance sheet with the four key dimensions, and keep a duplicate sample in Wuzhou. On a reorder the duplicate is opened and compared before the first piece is cast.
Minimum order is 50 pieces per design and sizes can be mixed. Sample lead time is around 20 days from approved CAD, bulk 25 to 30 days, and stock designs ship in 15 to 20 days under 500 pieces. Payment is a 30 percent deposit with the balance before shipment, by T/T, PayPal or Western Union, with volume pricing at 200 and 500 pieces.
[11]What the sample does not cover
A sample does not cover the size range. A 6 mm sample approved for a run of 5 to 9 mm tells you nothing about the 9 mm, because the shank thickness and the weight change with size.
The sample also does not cover the stone range. A sample set with one grade does not show what the parcel will look like across the run, and the spread is the thing a buyer notices at delivery.
A complete approval covers three sizes at the ends and the middle and one piece from each colour grade in the parcel.
[12]What travels with the bulk order
Four documents travel with the goods: the signed tolerance sheet, the stone record, the plating specification and the invoice. Those four let the buyer's own inspection check the same numbers the factory checked.
An order that ships without them cannot be inspected against anything, and the inspection becomes a visual opinion rather than a measurement.
The cost of those four documents is a few pages of paper, and they are the difference between a delivery that is accepted and one that is argued.
[13]Frequently Asked Questions
Do I need a golden sample for every order?
For every new design, and for every reorder where the specification changed. A repeat order with no change can reference the previous sample.
Who keeps the golden sample?
Both parties keep one. A single sample held by the factory is not a control, because the buyer has nothing to compare against.
What tolerance is normal on a band width?
Plus or minus 0.15 mm on a cast band and 0.1 mm on a machined band. Tighter than that requires machining rather than casting.
Can a photo replace a sample?
No. A photo shows appearance and hides weight, finish and feel, which are the three things a sample exists to fix.
[14]Next step
Send the design and the dimensions that matter, and we will return a sample with a tolerance sheet. See OEM work in the archive, read the journal on factory quoting, or open a brief on the contact page.