Free express shipping over $99 GRA & IGI certificates Quote in 1 business day

Journal / Lab Grown Diamond

Lab-Grown Melee Checks Before Setting
HOLYCOME / NOTESLab Grown Diamond  ●  9 November 2026  ●  8 MIN

Lab-Grown Melee Checks Before Setting

A setter in Bangkok returned a tray of 1.3 mm lab-grown melee because half the stones would not sit level in a channel. The stones were the stated size, the channel was the stated depth, and the failure was in the parcel: mixed girdle thickness.

Melee is bought by sieve size, and a sieve range is a diameter band, not a thickness specification. A parcel that spans 1.25 to 1.40 mm in diameter can also span three girdle thicknesses, and only two of those set level in a channel cut for one.

[1]Why melee fails where larger stones do not

Above 0.20 ct a stone is set individually, with a seat cut to that stone. Below that, stones are set in lines and the line is cut once. A parcel that varies in the dimension the line depends on will fail at the bench, not at the grading table.

This is why melee buying is a specification exercise rather than a grading exercise. The report matters, and the geometry matters more.

Sieve size and what it does not promise

Sieve sizes are defined in standard bands, and a parcel sold as a single sieve contains stones within that band. It says nothing about girdle thickness, table size or depth percentage, which is where the variation that breaks a channel lives.

Girdle thickness

Channel setting holds the stone at the girdle. Two stones of the same diameter but different girdle thickness sit at different heights, and the channel cannot be cut to suit both. A mixed parcel produces a line that looks wavy in a side view, which is the failure the setter described.

Depth percentage

Depth percentage below roughly 58 percent produces a shallow stone that returns less light from a glancing angle. Above 64 percent, the pavilion approaches the girdle and the stone becomes harder to seat without exposing the culet.

Emerald cut loose gemstone photographed on a pale display surface with report paper behind it

[2]The four checks we run on incoming melee

Each check catches a different failure, and skipping any one moves the problem to a more expensive stage.

CheckMethodPass criterionFailure it catches
Sieve consistencyGauge or sieve set95 percent within stated bandLine that reads uneven in length
Girdle thicknessMicroscope, 20x, 30 stonesSpread under 0.05 mmWavy line in a channel
Depth percentageProportion estimate at 20x58-64 percentFlat stones or exposed culets
Damage and beardingLoupe, full trayNo chips at girdleStones that break during setting

[3]Sampling that actually protects the order

Thirty stones from a 5,000 stone parcel is a small sample, and it is enough to detect a mixed parcel because mixing is a batch property rather than a random one. A parcel sourced from one production run tends to be consistent; a parcel assembled from several runs tends to vary across the whole tray.

Take the thirty from three positions: the top of the bag, the middle, and the bottom. Variation between positions is the signal that the parcel was assembled rather than produced.

Recording the sample

A sample that is not recorded is a sample that has to be repeated. We log the sieve range measured, the girdle spread observed, the number of stones checked and the position in the bag each stone came from, which is enough to compare a later parcel against the first one.

That log is also the document that settles a dispute about a parcel that set badly six months ago, because it records what the parcel looked like when it arrived.

When to escalate to full inspection

Escalate when the girdle spread exceeds 0.05 mm in the sample, when more than one stone shows girdle damage, or when the sieve band contains stones outside the stated range by more than 0.03 mm.

[4]Cost arithmetic

A melee parcel at 1.2 mm costs a fraction of a cent per stone in labour terms, and a failed channel costs a whole ring. The check is thirty minutes on a microscope; a re-set of forty rings is two days plus the melee that cannot be recovered from a cut channel. Add the polishing pass that has to be repeated after unsetting, and the check pays for itself on the first parcel that would have failed.

Buyers who skip the check usually discover the problem when the setter reports it, which is after the channel has been cut and sometimes after the ring has been polished.

[5]Specifying melee in a purchase order

Four lines in a purchase order prevent most of this. State the sieve band with a tolerance, state the maximum girdle spread, state the depth percentage range, and require a pre-shipment photo of the tray at magnification. Put the acceptance figure on paper as well, so a parcel that fails is rejected at receiving rather than negotiated after the channel has been cut.

  • Sieve band with tolerance, for example 1.20-1.30 mm plus or minus 0.02 mm
  • Girdle spread maximum 0.05 mm across the parcel
  • Depth percentage 58 to 64 percent
  • No girdle chips, verified at 10x before packing

[6]The setting method decides the spec

Different settings load the stone in different places, so the melee specification should follow the setting rather than the other way round. A parcel bought to a generic spec will fit one setting and fight another.

Channel and shared-prong lines

These hold the girdle and set the height once for the whole run. The parcel must be narrow in both diameter and girdle thickness, and depth percentage matters because the stones sit at one level. This is the most demanding specification and where most failures appear.

Individual prong and bezel settings

Each stone gets its own seat, so diameter variation can be absorbed by the setter. A mixed parcel is workable here, and the practical limit is the time the setter spends adjusting seats rather than the stone geometry.

Pavé with a cut seat per stone

Pavé sits between the two. Each stone has a seat, and the line still has to read as a continuous surface. A parcel with a small girdle spread works; a parcel assembled from several runs usually does not.

[7]How melee is priced

Melee is quoted per carat, and a carat of 1.2 mm stones is several hundred pieces, so the per-carat number hides the per-piece number that matters for costing a ring. Buyers who cost a line from a per-carat quote without a piece count usually under-estimate the melee content of a ring by a wide margin.

Ask for both numbers on any quotation: the per-carat price and the approximate piece count per carat at the specified sieve. With those two figures, the melee cost per ring becomes an arithmetic step rather than an assumption.

Sorting, matched parcels and documentation each add a small premium, and each removes a category of rework. On a production line of any size, the premium is cheaper than the rework it prevents.

[8]What we supply on melee orders

Melee parcels ship with the sieve band and girdle spread recorded on the packing list, and trays above 2,000 stones are photographed at magnification before packing. Stones that fail our own bench check are removed before the parcel is closed, not after the buyer reports them.

Minimum order is 50 pieces per design for finished work; loose melee is quoted per carat with a minimum lot value. Sample lead time is around 20 days, bulk 25 to 30 days, and stock designs ship in 15 to 20 days under 500 pieces. Payment is a 30 percent deposit with the balance before shipment, by T/T, PayPal or Western Union, with volume steps at 200 and 500 pieces.

[9]Frequently Asked Questions

Can a mixed melee parcel still be used?

Yes, in settings that hold each stone individually, such as a bezel or a prong setting with a cut seat per stone. It cannot be used in a channel or a shared line where the height is set once for the whole run.

Is 1.3 mm melee graded?

Usually not individually. Melee below roughly 0.20 ct is sold as a parcel with a stated colour and clarity range, and the report covers the parcel rather than each stone.

What causes bearding on melee?

Cutting speed and polishing pressure at the girdle. It appears as a feathered edge that chips during setting, and it is invisible until the stone is under pressure in a seat.

How many carats are in a 1.2 mm parcel of 1,000 stones?

Roughly 0.9 to 1.0 carat total, depending on depth. The exact figure depends on the cut, so a per-carat quote should always be confirmed against a counted and weighed parcel.

[10]Next step

Send the sieve band and the setting type, and we will quote a parcel specified to the line rather than to a grade range. See finished channel and pavé work in the archive, read the journal on fluorescence sorting, or open a parcel enquiry on the contact page.

Ready when you are

Send a photograph. Get the price tomorrow.

Request a quote WhatsApp us

MOQ for a single commission is 1 piece; wholesale MOQ is 20 pcs per style. Sampling takes 7-14 days, bulk 15-25 days after CAD approval. Payment is T/T with a 30% deposit, balance before shipment; PayPal and major cards are accepted.

Every piece passes a quality check before dispatch, and authenticity is matched to its certificate, with a return policy and repair service after delivery. Our in-house jewelers and artisans have years of experience setting moissanite and lab-grown stones from responsible, traceable suppliers; customer reviews and commission testimonials are shared in our journal and on the about page. Questions? Email service@holycome.com or WhatsApp +86 13377447107.

WhatsApp us Get a quote
WhatsApp Email