Free express shipping over $99 GRA & IGI certificates Quote in 1 business day

Journal / Lab Grown Diamond

Lab Grown Diamond: Vetting a Factory: Seven - HOLYCOME
HOLYCOME / NOTESLab Grown Diamond  ●  16 November 2026  ●  6 MIN

Lab Grown Diamond: Vetting a Factory: Seven - HOLYCOME

We spend most of our time on diamond, so this guide is written from what comes back to the bench: the pieces that reorder, the complaints that should have been prevented, and the price lines that survive a marketplace margin. Treat the figures below as planning anchors rather than a fixed quotation; metal and stone costs move, and every lot is priced on its own specification.

A first sample tells you more than a catalogue of five. On the sample, check the band or shank weight against the spec, look at the plating under a loupe at the high-friction points, confirm the stone sits level and the prongs sit above the girdle, and weigh the piece. A hollow or underweight body is the first thing a repeat order exposes.

Ask for the certificate and the alloy declaration in writing. A GRA or batch card declares grade and carat; it is not the same as an independent laboratory report, and the listing should say which one applies. For metal, the alloy sheet states the silver grade or the gold karat and confirms whether any nickel is added, which matters for customers with sensitive skin.

Reject on documented defects, not on taste: a tilted stone, a prong on the table, a plating gap at the inner shank, or a weight under spec are all measurable. Photograph the batch before it leaves the bench so a later complaint has a baseline. A supplier that pushes back on a documented defect is one you will spend the whole order negotiating with.

[1]Diamond: the practical checks before you order

  • Weigh the piece against the listed weight; an underweight shank or body is usually the first sign of a thin build.
  • Check the plating or finish at the high-friction points under a loupe, where wear shows first.
  • Verify the prongs sit above the girdle and the stone sits level; a tilted stone reads as a cheap setting in any photo.
  • Match the certificate number to the card before listing, and keep the batch sheet with the order records.
  • Ask for the alloy declaration and confirm whether any nickel is added, especially for skin-sensitive customers.

[2]Planning the first run

After the lot arrives, compare it against the sample you approved rather than against the photograph. Weight, finish, stone match and setting position are the things that drift between sample and bulk, and they are measurable. Keep the arrival photos with the order record so a later exchange or a reorder starts from the same baseline.

When you plan the order, work backwards from the sell-through you can actually predict. A first batch that covers six to eight weeks of sales is easier to correct than a deep run that ties up cash in a style the market has not answered yet. Once the reorder pattern shows, the second buy can go wider on the silhouettes that moved first.

[3]Reference range in our catalogue

ReferenceSpecificationMOQUnit range
Custom Private Label Lab-Grown Diamond Round Loose MLab-Grown Diamond · 925 Sterling Silver1on request
Factory-Direct Lab-Grown Diamond Round Loose MoissanLab-Grown Diamond · 925 Sterling Silver1on request
Factory-Direct Lab-Grown Diamond Round Loose MoissanLab-Grown Diamond · 925 Sterling Silver1on request
Factory-Direct Lab-Grown Diamond Round Loose MoissanLab-Grown Diamond · 925 Sterling Silver1on request
Wholesale Lab-Grown Diamond Round Lab-Grown GemstoneLab-Grown Diamond · 925 Sterling Silver1on request

Ranges reflect current factory pricing for this catalogue and move with metal and stone costs; treat them as planning figures and confirm against a written quotation.

We would not advise buying on the lowest quote alone. A unit price that sits well under the market usually comes back as a plating, weight or grade problem later, which costs more than the few cents saved per piece.

The practical takeaway is straightforward: read the spec sheet before the price, hold the sample before the bulk, and judge the lot on weight, finish and stone match rather than on listing imagery. Do that consistently and the repeat orders mostly take care of themselves.

[4]Buyer questions

What should I check on the first sample?

Weight against spec, plating under a loupe at friction points, stone levelness, prong position and overall weigh-in. Photograph the sample on arrival as the baseline for the bulk lot.

Which certificate or declaration matters?

The stone card or report number and the alloy declaration. Confirm whether the certificate is a batch card or a per-stone report, and keep the number matched to the parcel records.

Can I order a sample before committing to bulk?

Yes. A sample from stock lets you judge weight, finish and communication before the bulk run; compare it against the spec sheet and keep arrival photos for the later comparison.

[5]Related reading

Ready when you are

Send a photograph. Get the price tomorrow.

Request a quote WhatsApp us

MOQ for a single commission is 1 piece; wholesale MOQ is 20 pcs per style. Sampling takes 7-14 days, bulk 15-25 days after CAD approval. Payment is T/T with a 30% deposit, balance before shipment; PayPal and major cards are accepted.

Every piece passes a quality check before dispatch, and authenticity is matched to its certificate, with a return policy and repair service after delivery. Our in-house jewelers and artisans have years of experience setting moissanite and lab-grown stones from responsible, traceable suppliers; customer reviews and commission testimonials are shared in our journal and on the about page. Questions? Email service@holycome.com or WhatsApp +86 13377447107.

WhatsApp us Get a quote
WhatsApp Email