Journal / Jewelry Care
Jewellery Plating Thickness and Wear Testing
A brand in Austin ordered 200 rhodium plated silver rings with a plate specified as standard. Six months later 40 were showing yellow, and the whole batch had to be reworked or refunded.
The word standard covered 0.1 to 1.5 micron, and the brand had been sold the bottom of that range without knowing it was a range at all.
[1]What plate thickness means
Thickness is measured in microns, and one micron is a thousandth of a millimetre. A rhodium plate of 0.8 to 1.2 micron is the usual commercial range for a ring that will be worn daily.
Below 0.5 micron the plate is decorative rather than protective, and it will wear through at the high points within a few months. Above 2 micron the plate can crack at a sharp bevel, which looks worse than uniform wear.
| Thickness | Life in daily wear | Best use |
|---|---|---|
| 0.1 to 0.3 micron | 2 to 4 months | Sample only |
| 0.5 micron | 5 to 9 months | Occasional wear |
| 0.8 to 1.2 micron | 12 to 24 months | Daily wear |
| 1.5 to 2 micron | 24 to 36 months | Heavy wear |
The table assumes a normal wear profile and a correct prep. A plate over a polished but contaminated surface can fail in weeks regardless of its thickness.

[2]The prep before the plate
Plating is a deposition process, and deposition requires a clean and activated surface. Three prep failures account for most early plate failures: residual polishing compound, oxidation from a delay between polish and plate, and an insufficient strike layer.
The strike layer is a thin intermediate deposit that bonds the plate to the base metal. A plate applied without a strike can look correct on arrival and peel in wear, because the bond is between the plate and the contamination rather than the metal.
How prep is verified
A water break test is the simplest check: a clean surface holds a continuous water film for 30 seconds. A surface that breaks into droplets has residual oil and will produce a weak plate.
That test costs nothing and catches the failure before the plating bath rather than after the shipment.
[3]Wear testing before bulk
A wear test is not an accelerated cycle in a machine. It is a real wear test on a small set of rings by people who wear them daily, for at least four weeks.
Four weeks of real wear shows the high points where the plate will fail first, which are the same points on every ring of the design. Those points are where the plate should be checked at 100x, and where a thicker plate does the most good.
The salt spray question
A salt spray test measures corrosion resistance rather than wear resistance, and it is not a substitute for a wear test. A ring can pass 24 hours of salt spray and still wear through at the shank in three months.
[4]Adhesion testing
Adhesion is tested by a tape pull or a thermal cycle. A tape pull on a test coupon lifts the plate if the bond is weak; a thermal cycle opens cracks that a visual check misses.
Neither test is destructive in a way that costs much, and both should run on the first piece of every plating lot rather than on the finished batch.
What a cross section shows
A cross section under a microscope shows the plate thickness directly, which is the number the buyer is paying for. A supplier who cannot provide a cross section measurement is not measuring the plate at all.
[5]The base metal beneath the plate
Plating is a thin layer over a base, and the base decides how the plate behaves. A brass base is harder than a silver base and holds a plate longer under abrasion, and it also looks different when the plate wears through.
A brass base that shows through a white plate shows yellow, which is the most visible failure. A silver base shows white-grey, which is closer to the plate colour and hides wear for a few more weeks.
Where the base matters most
At the high points and at the edges. A bevel that carries a sharp edge will wear the plate first, because the plate thickness at an edge is always less than on a flat surface.
A buyer can specify a rounded bevel, which spreads the wear over a wider band and extends the plate life without changing the appearance from arm's length.
[6]Colour matching across a lot
A plating lot is a series of baths, and each bath produces a slightly different colour. A lot of 200 pieces plated across four baths can show four shades, which reads as four products on a shelf.
The control is a colour standard and a bath change at a fixed piece count, rather than a bath change when the solution looks tired.
How the standard is held
A physical standard piece is kept from the approved first bath, and every subsequent bath is compared against it under a fixed light. A visual comparison under daylight is enough for white plates, which have little colour variation to measure.
What a mismatch costs
A returned lot for colour mismatch costs a re-plate plus freight plus the shelf time. That is more than the cost of the extra bath changes that would have prevented it.
[7]What the invoice should carry
Four lines: the plate metal, the thickness in microns, the base metal and the prep method. A buyer with those four can compare two suppliers on the same terms rather than on the word standard.
[8]What a wear claim tells a supplier
A claim with photographs of the worn points is the most useful feedback a plating line receives. It shows which surface wore first, which is a function of the design rather than of the plate.
A claim that says the plate failed without a photograph cannot be diagnosed, and it usually results in the same specification being repeated with the same failure.
Where claims cluster
Three places: the shank at the palm side, the inside of the finger at the joint, and the edges of a bevel. Those are the three highest contact points on a ring, and they are where a plate should be checked first.
A design that puts a sharp edge at a contact point will always wear there first, regardless of the plate. Rounded edges at contact points extend plate life more than a thicker plate does.
[9]Setting a plate specification with a brand
A brand specification should state four numbers: plate metal, thickness, base metal and the wear test result. Those four are enough for any supplier to quote the same product.
A specification that says only the colour is a specification that allows any thickness, and the cheapest supplier will choose the thinnest one that passes a visual check.
[10]What we specify
We specify the plate metal, the thickness in microns, the strike layer and the prep method on the order, and we send a cross section measurement with the first lot. That is the difference between a plate that lasts a year and a plate that lasts a quarter.
Minimum order is 50 pieces per design and sizes can be mixed. Sample lead time is around 20 days from approved CAD, bulk 25 to 30 days, and stock designs ship in 15 to 20 days under 500 pieces. Payment is a 30 percent deposit with the balance before shipment, by T/T, PayPal or Western Union, with volume pricing at 200 and 500 pieces.
[11]The high point is the first failure
Every plated piece has a high point, and the plate is thinnest there because deposition follows the surface rather than filling it. A prong tip and a shank edge are the two high points on most rings.
A plate that is 1 micron on the flat is 0.6 to 0.8 micron at a sharp edge, which is why a sharp design wears through a nominal 1 micron plate in half the expected time.
Rounding the high points is the cheapest way to extend plate life, and it is a CAD change rather than a plating change.
[12]Frequently Asked Questions
How thick should rhodium plating be on a silver ring?
0.8 to 1.2 micron for daily wear and 1.5 to 2 micron for heavy wear. Below 0.5 micron is sample grade and wears through in months.
Does a thicker plate always last longer?
No. Above about 2 micron the plate can crack at sharp bevels, and a cracked plate fails faster than a thinner even one.
Can plating hide a bad finish?
Only briefly. A plate over a scratched or contaminated surface looks correct and fails early, because the bond is to the contamination rather than to the metal.
Is salt spray the same as wear testing?
No. Salt spray measures corrosion and wear testing measures abrasion. A ring can pass salt spray and still wear through at the shank.
[13]Next step
Send the base metal, the wear profile and the finish, and we will specify the plate thickness and the prep. See plated work in the archive, read the journal on tarnish storage, or open an order on the custom page.