Journal / Jewelry Care
Care & Maintenance Spec Sheets: Six Fields - HOLYCOME
This guide walks a wholesale or boutique buyer through this jewellery category the way our bench would talk it through on a sample day: what the order actually consists of, where the cost sits, and the checks that decide whether the lot lands clean on your shelf. No catalogue adjectives, just the numbers and the decisions we see buyers get wrong most often.
Tell your customers the expected finish interval up front. A plated silver piece worn daily shows the base metal at high-friction points within months, and that is normal wear rather than a defect. A care card that sets the expectation reduces the "it looks cheap" complaint that really means "the plating wore off sooner than I expected".
Day-to-day wear does the damage, not a single accident. Moisture, perfume, sweat and friction against a handbag or a desk are what dull the surface and loosen a prong over time. The care routine that actually works is short: wear last, take off before showering or cleaning, and store the piece separately so it is not rubbing against other metal in the box.
Cleaning should stay gentle. Warm water, a drop of mild soap and a soft brush on the setting and under the stone is enough for most silver and plated pieces; ultrasonic cleaning on a regular basis can loosen prongs and drive moisture behind a plated layer. If the plating has worn through at the contact points, replating is a bench job, not something a polishing cloth fixes.
[1]This jewellery category: the practical checks before you order
- Check the plating or finish at the high-friction points under a loupe, where wear shows first.
- Verify the prongs sit above the girdle and the stone sits level; a tilted stone reads as a cheap setting in any photo.
- Match the certificate number to the card before listing, and keep the batch sheet with the order records.
- Ask for the alloy declaration and confirm whether any nickel is added, especially for skin-sensitive customers.
- Confirm the size run, the millimeter measurements and the chain or band width on the listing.
[2]Planning the first run
Mixing the range on the first order is a judgment call. A small number of proven designs at a workable MOQ gives the bench less to set up and the buyer fewer decisions to defend if something underperforms. Reserve the experimental finishes and newer shapes for a later batch, once the core of the catalogue has proved itself with your customers.
Payment and sample terms should be settled before production starts. A sample order, the approved spec sheet, and the deposit schedule are the three documents that keep a bulk run from becoming a negotiation halfway through. If a supplier is vague on which of these are written down, that vagueness usually repeats on delivery day.
[3]Reference range in our catalogue
| Reference | Specification | MOQ | Unit range |
|---|---|---|---|
| Wholesale Manufacturer Lab-Grown Diamond Round Neckl | Lab-Grown Diamond · 925 Sterling Silver | 1 | on request |
| Factory-Direct Lab-Grown Diamond Round Necklaces in | Lab-Grown Diamond · 925 Sterling Silver | 1 | on request |
| Square Bezel Moissanite Engagement Ring | Moissanite · 925 Sterling Silver | 1 | on request |
| Pear Lab-Grown Gemstone Pendant | Lab-Grown · 925 Sterling Silver | 1 | on request |
| Wholesale Lab-Grown Diamond Round Jewelry Sets in 92 | Lab-Grown Diamond · 925 Sterling Silver | 1 | on request |
Ranges reflect current factory pricing for this catalogue and move with metal and stone costs; treat them as planning figures and confirm against a written quotation.
In our experience, most disputes on a wholesale order come from a spec that was spoken rather than written. The weight, the plating micron and the stone grade should appear on the order or the spec sheet, not only in the chat.
If you are putting together a first run in this category, start with the stock silhouettes, keep the size run standard, and let the sell-through decide where the next batch expands. That approach protects margin better than chasing the widest catalogue on day one.
[4]Buyer questions
How often should the piece be cleaned?
A gentle soap-and-water clean every couple of weeks for worn daily pieces is enough. Avoid regular ultrasonic cleaning on plated or prong-set pieces, which can loosen settings and drive moisture behind plating.
What damages the finish fastest?
Perfume, sweat, moisture and friction against other metal wear the surface down fastest. Take the piece off before showering or cleaning, and store it separately from other jewellery so the plating is not rubbed through in the box.
Can I order a sample before committing to bulk?
Yes. A sample from stock lets you judge weight, finish and communication before the bulk run; compare it against the spec sheet and keep arrival photos for the later comparison.
[5]Related reading
Read Returns and Claims: How Necklaces Defects Get for the deeper walk-through.
Read Brand Pack: Photos, Spec Sheet and Listing CSV for the deeper walk-through.