Journal / Jewelry Care
Repair and Refinish Path for Care & Maintenance - HOLYCOME
This guide walks a wholesale or boutique buyer through this jewellery category the way our bench would talk it through on a sample day: what the order actually consists of, where the cost sits, and the checks that decide whether the lot lands clean on your shelf. No catalogue adjectives, just the numbers and the decisions we see buyers get wrong most often.
Tell your customers the expected finish interval up front. A plated silver piece worn daily shows the base metal at high-friction points within months, and that is normal wear rather than a defect. A care card that sets the expectation reduces the "it looks cheap" complaint that really means "the plating wore off sooner than I expected".
Day-to-day wear does the damage, not a single accident. Moisture, perfume, sweat and friction against a handbag or a desk are what dull the surface and loosen a prong over time. The care routine that actually works is short: wear last, take off before showering or cleaning, and store the piece separately so it is not rubbing against other metal in the box.
Cleaning should stay gentle. Warm water, a drop of mild soap and a soft brush on the setting and under the stone is enough for most silver and plated pieces; ultrasonic cleaning on a regular basis can loosen prongs and drive moisture behind a plated layer. If the plating has worn through at the contact points, replating is a bench job, not something a polishing cloth fixes.
[1]This jewellery category: the practical checks before you order
- Ask for the alloy declaration and confirm whether any nickel is added, especially for skin-sensitive customers.
- Confirm the size run, the millimeter measurements and the chain or band width on the listing.
- Photograph the batch on arrival so any later defect claim has a baseline to compare against.
- Confirm the stone grade and carat on the spec sheet, and note whether it ships on a batch card or a per-stone report.
- Weigh the piece against the listed weight; an underweight shank or body is usually the first sign of a thin build.
[2]Planning the first run
Payment and sample terms should be settled before production starts. A sample order, the approved spec sheet, and the deposit schedule are the three documents that keep a bulk run from becoming a negotiation halfway through. If a supplier is vague on which of these are written down, that vagueness usually repeats on delivery day.
After the lot arrives, compare it against the sample you approved rather than against the photograph. Weight, finish, stone match and setting position are the things that drift between sample and bulk, and they are measurable. Keep the arrival photos with the order record so a later exchange or a reorder starts from the same baseline.
[3]Reference range in our catalogue
| Reference | Specification | MOQ | Unit range |
|---|---|---|---|
| Pear Moissanite Jewelry Set | Moissanite · 925 Sterling Silver | 1 | on request |
| Custom Private Label Lab-Grown Diamond Round Earring | Lab-Grown Diamond · 925 Sterling Silver | 1 | on request |
| Factory-Direct Emerald Emerald Necklaces in 925 Ster | Emerald · 925 Sterling Silver | 1 | on request |
| Wholesale Lab-Grown Diamond Round Bracelets in 925 S | Lab-Grown Diamond · 925 Sterling Silver | 1 | on request |
| Green Round Zirconia Stone | Zirconia · 925 Sterling Silver | 1 | on request |
Ranges reflect current factory pricing for this catalogue and move with metal and stone costs; treat them as planning figures and confirm against a written quotation.
We would not advise buying on the lowest quote alone. A unit price that sits well under the market usually comes back as a plating, weight or grade problem later, which costs more than the few cents saved per piece.
The practical takeaway is straightforward: read the spec sheet before the price, hold the sample before the bulk, and judge the lot on weight, finish and stone match rather than on listing imagery. Do that consistently and the repeat orders mostly take care of themselves.
[4]Buyer questions
How often should the piece be cleaned?
A gentle soap-and-water clean every couple of weeks for worn daily pieces is enough. Avoid regular ultrasonic cleaning on plated or prong-set pieces, which can loosen settings and drive moisture behind plating.
What damages the finish fastest?
Perfume, sweat, moisture and friction against other metal wear the surface down fastest. Take the piece off before showering or cleaning, and store it separately from other jewellery so the plating is not rubbed through in the box.
Can I order a sample before committing to bulk?
Yes. A sample from stock lets you judge weight, finish and communication before the bulk run; compare it against the spec sheet and keep arrival photos for the later comparison.
[5]Related reading
Read Fashion Rings Factory Direct: returns and repair data for the deeper walk-through.
Read Fashion Rings Small MOQ for Resale: custom CAD to sample workflow for the deeper walk-through.