Free express shipping over $99 GRA & IGI certificates Quote in 1 business day

Journal / Custom Engagement Rings

Custom Engagement Rings: Cost Breakdown: The - HOLYCOME
HOLYCOME / NOTESCustom Engagement Rings  ●  16 November 2026  ●  6 MIN

Custom Engagement Rings: Cost Breakdown: The - HOLYCOME

We spend most of our time on rings and ring, so this guide is written from what comes back to the bench: the pieces that reorder, the complaints that should have been prevented, and the price lines that survive a marketplace margin. Treat the figures below as planning anchors rather than a fixed quotation; metal and stone costs move, and every lot is priced on its own specification.

Unit price improves quickly with quantity because the setup cost — mould pass, stone matching, plating bath — is spread across more pieces. The setup is why a single sample costs more per piece than a bulk run, and why ordering a slightly larger quantity at a slightly lower MOQ tier often beats pushing the MOQ down to one.

There are cost lines you should not cut to win a cheaper quote. A thinner band, lighter plating or a lower stone grade saves a few cents per piece and shows up in the return rate. If a quote comes in well under the rest, ask for the weight, the plating micron and the stone grade on paper before you compare the headline number.

The wholesale price breaks into four broad lines: the metal, the stone, the bench labour, and the overhead that covers plating, certificate, packaging and export handling. Of those, labour and plating are the two a supplier can move honestly, while the stone line follows grade and carat. When a quote looks unusually low, the first place to look is the plating thickness and the shank weight, not the branding.

[1]Rings and ring: the practical checks before you order

  • Confirm the size run, the millimeter measurements and the chain or band width on the listing.
  • Photograph the batch on arrival so any later defect claim has a baseline to compare against.
  • Confirm the stone grade and carat on the spec sheet, and note whether it ships on a batch card or a per-stone report.
  • Weigh the piece against the listed weight; an underweight shank or body is usually the first sign of a thin build.
  • Check the plating or finish at the high-friction points under a loupe, where wear shows first.

[2]Planning the first run

Payment and sample terms should be settled before production starts. A sample order, the approved spec sheet, and the deposit schedule are the three documents that keep a bulk run from becoming a negotiation halfway through. If a supplier is vague on which of these are written down, that vagueness usually repeats on delivery day.

After the lot arrives, compare it against the sample you approved rather than against the photograph. Weight, finish, stone match and setting position are the things that drift between sample and bulk, and they are measurable. Keep the arrival photos with the order record so a later exchange or a reorder starts from the same baseline.

[3]Reference range in our catalogue

ReferenceSpecificationMOQUnit range
Bulk OEM Lab-Grown Diamond Round Earrings in 925 SteLab-Grown Diamond · 925 Sterling Silver1on request
Custom Private Label Lab-Grown Diamond Round Rings iLab-Grown Diamond · 925 Sterling Silver1on request
Classic Six-Prong Moissanite Engagement RingMoissanite · 925 Sterling Silver1on request
Round Moissanite Ring, GRA Certified — Design 62Moissanite · 925 Sterling Silver1on request
Moissanite Engagement Ring MA036Moissanite · 925 Sterling Silver1on request

Ranges reflect current factory pricing for this catalogue and move with metal and stone costs; treat them as planning figures and confirm against a written quotation.

[4]Where the wholesale price sits

ComponentShareAt $28.00 per piece
Metal and casting18%$5.04
Stone and setting35%$9.80
Labour and finishing19%$5.32
Plating and surface10%$2.80
Certificate and packaging6%$1.68
Margin and export handling14%$3.92

We would not advise buying on the lowest quote alone. A unit price that sits well under the market usually comes back as a plating, weight or grade problem later, which costs more than the few cents saved per piece.

The practical takeaway is straightforward: read the spec sheet before the price, hold the sample before the bulk, and judge the lot on weight, finish and stone match rather than on listing imagery. Do that consistently and the repeat orders mostly take care of themselves.

[5]Buyer questions

What makes up the wholesale price?

Metal, stone, bench labour and the overhead for plating, certificate, packaging and export handling. Labour and plating are the lines a supplier can adjust honestly; the stone line follows grade and carat.

Where can cost be cut honestly without hurting quality?

Packaging tier, order quantity and size run are the cleanest places to adjust. Metal weight, plating thickness and stone grade are the lines not to cut, because those savings return as after-sales problems.

Can I order a sample before committing to bulk?

Yes. A sample from stock lets you judge weight, finish and communication before the bulk run; compare it against the spec sheet and keep arrival photos for the later comparison.

[6]Related reading

Ready when you are

Send a photograph. Get the price tomorrow.

Request a quote WhatsApp us

MOQ for a single commission is 1 piece; wholesale MOQ is 20 pcs per style. Sampling takes 7-14 days, bulk 15-25 days after CAD approval. Payment is T/T with a 30% deposit, balance before shipment; PayPal and major cards are accepted.

Every piece passes a quality check before dispatch, and authenticity is matched to its certificate, with a return policy and repair service after delivery. Our in-house jewelers and artisans have years of experience setting moissanite and lab-grown stones from responsible, traceable suppliers; customer reviews and commission testimonials are shared in our journal and on the about page. Questions? Email service@holycome.com or WhatsApp +86 13377447107.

WhatsApp us Get a quote
WhatsApp Email