Free express shipping over $99 GRA & IGI certificates Quote in 1 business day

Journal / Wholesale Oem Factory

Bracelets Factory Direct: What a Lot Inspection - HOLYCOME
HOLYCOME / NOTESWholesale Oem Factory  ●  10 November 2026  ●  5 MIN

Bracelets Factory Direct: What a Lot Inspection - HOLYCOME

[1]Answer First, Sampling After

The answer most buyers get is a percentage, and a percentage is not a protocol. Three things make an inspection real: a written spec, a sampling plan tied to the lot size, and a reject rule that someone signs. This page sets out all three as we apply them to bracelets.

[2]The Sampling Plan We Work To

Read the row for your lot size and ignore the rest. The important column is the last one, because that is the decision, and a decision with no owner is the reason claims turn into email threads, which is where most bracelets claims actually start.

Bracelets wholesale piece from the HOLYCOME line in Wuzhou
Lot sizeSampleCriticalMajorMinor
50 to 150 pieces13 piecesZero23
151 to 500 pieces32 piecesZero35
501 to 1,200 pieces50 piecesZero57
Over 1,200 pieces80 piecesZero710

The numbers above are the plan we quote. A buyer with a marketplace claim history may want a tighter major level, and that is a line worth paying for rather than arguing about after arrival, and at USD 34-220 for bracelets it is the one line that cannot be recovered later.

[3]The Sequence We Run on Every Lot

  1. Stone intake: verify the report number against the laser inscription, measure the mm size against the sieve range, and pull any stone outside the band. This station catches the failure that costs the most to fix later, and it costs one gemologist and a loupe.
  2. Casting inspection before plating: check porosity, shank thickness and joint integrity. Plating a porous casting hides the problem for six weeks and then returns it as a blister, which is why this station exists before the plating bath rather than after it.
  3. Setting check: prong tension, seat depth and stone height on a sample of every tray, not on the first piece of the run. A setter who is having a good morning is not evidence about the afternoon shift.
  4. Sizing and gauge: run a go/no-go gauge on every size in the lot and record the drift. A drift of 0.3 mm across a size run becomes a reship for the same order, and the gauge is what prevents it.
  5. Plating and finish: log the micron per lot, inspect under a 10x loupe at the prong tips where wear shows first, and check the colour against the retained master stone rather than against the previous tray.
  6. Final and pack: weigh, count, and reconcile the packing list fields against the carton. This is the station where a missing SKU is caught by paper instead of by the customer, and it takes ten minutes per carton.

Six stations sound like six costs. In practice the first three remove the reasons for the last three to reject anything, and the whole sequence adds a few minutes per tray rather than per piece, and bracelets at USD 34-220 is where this shows up first.

Nothing here needs a laboratory. A loupe, a gauge, a balance and a written sheet carry most of the quality a bracelets buyer is paying for, which is why the protocol travels with the trays.

A station without a signature is a station that did not happen. Ours carries the inspector's initials per lot, and the sheet ships in the carton so a claim can be argued from paper, which is where most bracelets claims actually start.

Bracelets setting and finish detail on a HOLYCOME factory sample

[4]Defect Classes and What Causes Them

DefectClassLikely causeFix at source
('clasp torsion failure', 'A box clasp rated for a necklace fails under wrist rotation. The clasp has to be tested in torsion, not only in pull.')MajorBench or spec gapGauge per size and a retained reference piece
('link gap growth', 'Gaps between links grow when the connecting pin is 0.05 mm under size. A pin gauge on every tenth piece catches it cheaply.')MajorPlating or casting prepPorosity check before the plating bath
('length drift on bangles', 'A bangle that measures 6.9 inch instead of 7.0 slides differently on the wrist. Oval versus round form changes the fit even at the same number.')Critical or majorComponent sourceIncoming check on the component lot
Colour drift against the masterMajorStone batchingMatched lot per tray, master stone on the bench
Sizing drift across the runMajorGauge not usedGo/no-go gauge on every size
Packing list mismatchMinor to majorDock reconciliationCarton count signed before sealing

Every row has a source upstream of the defect. Fixing the bracelet is a cost; fixing the row is a saving, and the difference is whether the cause is written down.

The first three rows account for most claims on bracelets. They are also the three that a bench check catches before packing, which is why the sequence matters more than the sample size.

A defect taxonomy is only useful if the words match across the order, the inspection and the claim. Ours uses the six terms above on the quote, the QC sheet and the credit note, and at USD 34-220 for bracelets it is the one line that cannot be recovered later.

[5]Who Owns a Failed Tray

One critical defect stops the lot and triggers a hundred percent check of the affected tray before anything ships. The buyer does not receive a percentage with a note attached; the tray is either reworked or held, which is where most bracelets claims actually start.

A major defect rate above the plan triggers a second sample on the same lot before a decision. The second sample decides whether the cause is the run or the tray, and both outcomes are written on the sheet the same day, and at USD 34-220 for bracelets it is the one line that cannot be recovered later.

A rejected tray is settled against the retained reference piece inside the same order cycle. If the difference shows on our retained piece we replace or credit; if it appeared in transit we split the assay cost and file with the carrier, and that split is on the order before the deposit clears, and bracelets at USD 34-220 is where this shows up first.

Minor defects inside the plan ship with the count stated on the packing list, so the buyer's receiving team knows what to expect rather than discovering it. Stating a minor defect is cheaper than hiding one, which is what bracelets at USD 34-220 actually buys.

The rule has to be signed before the run, because after the run it is a negotiation and the party holding the bracelets has the leverage. Writing it into the purchase order is the whole protection.

Buyers sometimes ask for a zero-defect clause. We quote it, and we quote the inspection cost that makes it possible, because zero without a hundred percent check is a promise rather than a process, and bracelets at USD 34-220 is where this shows up first.

A claim handled in the same cycle costs a credit note. A claim handled after the season costs the relationship, which is the more expensive of the two, which is what bracelets at USD 34-220 actually buys.

[6]When to Pay for an Outside Inspector

A third-party inspector adds independence, which matters when the factory is new to you and the order is large. It does not add specification: the inspector checks against the sheet you supply, so a vague sheet produces a vague report with a logo on it, and bracelets at USD 34-220 is where this shows up first.

The gap in most third-party reports is the retained reference. An inspector can measure a bracelet, but it cannot tell you whether the colour matches the master you approved, because it never saw the master. Send the reference piece with the inspection request.

Pay for an inspector on the first order above a few hundred pieces and on any order from a new factory. After two clean lots with the same spec, the money is better spent on your own receiving check and a gauge, which is where most bracelets claims actually start.

[7]Frequently Asked Questions

What AQL do you use for bracelets?

AQL 1.0 for major and 2.5 for minor on the lots above 150 pieces, with zero acceptance on critical defects. Below 150 pieces the lot is small enough that a hundred percent check on the bracelet costs less than a sampling argument.

How many pieces do you inspect on a 200-piece order?

32 pieces on a 200-piece run, pulled across trays rather than from one. Every size in the lot gets a gauge pass regardless of the sample, because drift is a run property and not a bracelet property.

Can I send my own inspector?

Yes. We schedule it, provide the trays and the sheet, and hold production until the report lands. Inspectors who arrive without the retained reference usually produce a report about appearance rather than about specification, and at USD 34-220 for bracelets it is the one line that cannot be recovered later.

What is a critical defect on Bracelets?

Stone loss, a prong that will not hold under load, a clasp that opens, or metal that fails a nickel or lead screen. One occurrence stops the lot; the others are counted against the plan, and bracelets at USD 34-220 is where this shows up first.

Do you inspect after plating or before?

Both, at different stations. Porosity is checked before the plating bath, and plating thickness and colour are checked after it. An inspection that only happens at the end cannot tell you which of the two failed, which is what bracelets at USD 34-220 actually buys.

[8]Next Step

Send the lot size and the defect history from your last order, and the reply comes back with the sampling plan, the six stations and the reject rule written for that lot rather than for a generic one, which is where most bracelets claims actually start.

HOLYCOME is the export arm of Wuzhou HengliLai Jewelry Co., Ltd., a Wuzhou, Guangxi plant that has shipped since 2009 and produces about 60,000 pieces a month, bracelets included. Export paperwork, the certificate pack and the packing list are prepared in-house, which is why the documents quoted on the order are the ones that travel with the carton. Reach the desk at service@holycome.com or WhatsApp +86 18078079070.

Related reading: Bracelets Factory Direct: 7 Supplier Checks Before You Pay - HOLYCOME Loose Stones Distributor Tier: How the Second Order Becomes Cheaper - HOLYCOME

Ready when you are

Send a photograph. Get the price tomorrow.

Request a quote WhatsApp us

MOQ for a single commission is 1 piece; wholesale MOQ is 20 pcs per style. Sampling takes 7-14 days, bulk 15-25 days after CAD approval. Payment is T/T with a 30% deposit, balance before shipment; PayPal and major cards are accepted.

Every piece passes a quality check before dispatch, and authenticity is matched to its certificate, with a return policy and repair service after delivery. Our in-house jewelers and artisans have years of experience setting moissanite and lab-grown stones from responsible, traceable suppliers; customer reviews and commission testimonials are shared in our journal and on the about page. Questions? Email service@holycome.com or WhatsApp +86 13377447107.

WhatsApp us Get a quote
WhatsApp Email